Tigerstop logo

TigerStop is an automated material stop gauge and positioner. It can push, pull, and position material, and will turn your existing machine into a lean manufacturing asset. TigerStop can push up to120 lbs. using roller tables, and quickly positions to your desired length and cuts within +/- .004" (.1mm) every time.

Call for information or to order - 920-452-4494

TigerStop Spare Parts - Page 2

If you don't see what you need, give us a call!

Rebuilt TigerStop Motors in Stock!
Why pay over $2,500 for a new motor, when we have rebuilt motors for $1,200. Call 920-452-4494 to order.

Solenoid Valve for Standard Interconnect KitSolenoid Valve

The solenoid valve for the Standard Interconnect Kit includes the following items:

  • 4 brass fittings (2x4mm and 2x6mm)
  • 1 muffler exhaust
  • 1 cable assembly (2-pinDC)

Part #: IKSV2
Price: $125

Spring BufferTigerstop Spring Buffer

The spring buffer is a flat pushing attachment for the TigerStop. The pushing surface is 6.5" x 3". The spring buffer reach can be adjusted from 10" - 23" beyond the leading edge of the flip away.
Part #: SB
Price: $695

Spring Buffer - Left HandTS Spring Buffer-Left Hand

This is a flat pushing attachment for the TigerTurbo or HeavyDuty 2. The pushing surface is 12.25" x 4". The heavy duty spring buffer reach is about 21.2" beyond the leading edge of the flip away. Left-handed means that the positioner is to the left of the integrated tool (ex: a TigerTurbo to the left of a drill press).
Part #: SBHD-L
Price: $1,515

Spring Buffer - Right HandTS Spring Buffer-RH

This is a flat pushing attachment for the TigerTurbo or HeavyDuty 2. The pushing surface is 12.25" x 4". The heavy duty spring buffer reach is about 21.2" beyond the leading edge of the flip away. Right-handed means that the positioner is to the right of the integrated tool (ex: a TigerTurbo to the right of a drill press).
Part #: SBHD-LR
Price: $1,515

Standard ControllerTS Standard Controller

The controller is the interface for most TigerStop positioners, and consists of a keypad and screen. Compatible with TigerStop, TigerFence (and SLR), TigerCrossCut, TigerTurbo, TigerRack, and HeavyDuty 2. Requires an amplifier (AMP6 or AMP5) and is not compatible with older controllers or with SawGear stop gauges.

Note: The CON5 price includes a $200 core charge refunded if the previous controller is returned to TigerStop within 30 days of the new shipment. CON5 orders require the serial number of the machine that will receive the electronics. Failure to use the controller with the specified serial number can result in software incompatibility issues.
Part #: CON5
Price: $2,070

Standard Controller CoverTS Controller Cover

Protective cover for Version 5 controllers. Made from clear plastic, protects the controller from metal and wood dust, and lubricants.
Part #: CON5CVR
Price: $75

Standard Interconnect KitTS Standard Interconnect Kit

The standard interconnect kit is one way of integrating TigerStop machinery with your tool. A roller switch is used to inform the positioner when the tool is at rest, preventing simultaneous movement of the two machines. Additionally, that communication allows for semi-automatic pushing operations. An included solenoid valve can optionally be used to prevent air to the tool unless the positioner is on, referenced, and motionless. Included are 4mm and 6mm fittings for the solenoid. For tools that aren't pneumatic, the 24 volts powering the solenoid could be used to drive a relay, with some wiring. SIK is compatible with TigerStop, TigerFence, TigerCrossCut, TigerTurbo, TigerRack, and HeavyDuty 2.

Part #: SIK
Price: $399

Steel Roller ReplacementTS Steel Roller

Replacement steel roller for 14" wide steel roller tables.

Part #: MR
Price: $50

Swivel Block AttachmentTS Swivel Block Attachment

TigerSPC is a statistical process control caliper set designed to be attached to the TigerStop table system with working lengths from 0-16 feet. The calipers can be equipped with a selection of both standard and custom attachments that allow it to be specifically configured for your set of critical quality control measurements.

The Swivel Block Attachment (SBA) allows operators to measure from hole center to hole center. it also swivels and can attach to other jaw accessories without losing tis reference point.

Jaw accessories include the following items:

Flat Jaws (FJ) allow operators to measure the distance between flat parts.

Mullion/Muntin Half Lap Jaws (HJ) allow operators to measure the center to center distance between to half lap joints.

Miter Jaws (MJ) allow the operator to measure the long side of miter cut pieces.

Part #: SBA
Price: $1,450

T-NutTS T-Nut

5/16" T-nut

Part #: TN
Price: $2

T-Nut MetricTS T-Nut Metric

MA T-nut

Part #: TN-MM
Price: $2

Table BracketsTS Table Brackets

These brackets attach the legs to the table for all flat TigerStop feed tables. They are incompatible with SawGear tables and with tilted TigerStop feed tables.

Contains two brackets, four binder rings, and a Table Hardware Pack (TABHP).

Part #: TABBR
Price: $200

Table Hardware PackTS Table hardware Pack

Feed table hardware pack. You will need one hardware pack per section of table/leg set.

Part #: TABHP
Price: $30

Thermal Transfer PrinterThermal Transfer Printer

Replacement 4" thermal transfer printer and cables.

Thermal transfer printers prevent ink from dissipating when exposed to direct sunlight for extended periods of time.

Part #: PRINTER-4T
Price: $1,599

TigerFence & TigerCrossCut Drive Belt

Part #: DB-RF
Price: $65

TigerFence & TigerCrossCut End Sensor
Idle End Sensor

The TigerFence & TigerCrossCut idle end sensor is also commonly called the far end sensor.

*Note: Not to be confused with the Tigerfence & TigerCrossCut Motor End Sensor (MES-RF). The two appear very similar, but the idle end sensor has longer cabling than the motor end sensor.

Part #: IES-RF
Price: $90

TigerFence & TigerCrossCut Motor
TigerFence Motor

The TigerFence & TigerCrossCut replacement motor.

Part #: MOT-TF
Price: $1,905

TigerFence & TigerCrossCut Motor End Sensor
TigerFence TigerCrossCut Motor End Sensor

TigerFence & TigerCrossCut motor end sensor.

*Note: Not to be confused with the Tigerfence &TigerCrossCut Idle End Sensor (IES-RF). The two appear very similar, but the motor end sensor has shorter cabling than the idle end sensor.

Part #: MES-RF
Price: $85

TigerRack Motor
TigerRack Motor

This is an AC motor for the TigerRack. It is incompatible with version 4 electronics.

Part #: MOT-TSR
Price: $2,725

TigerRack Motor Drive Belt

This belt connects the motor pulley to the pinion in a TigerRack

Part #: TR-DB
Price: $50

TigerRack Universal Mounting Bracket
TigerRack Universal Mounting Bracket

Part #: BR-TSR
Price: $50

TigerSaw 1000 and TigerSaw 2000 Light
TS1000 Light

This is a replacement pilot light for the TigerSaw 1000 and TigerSaw 2000.

Part #: J6730
Price: $5

TigerSaw 1000 Printer Cartridge
TS 1000 Printer Cartridge

This is a printer cartridge for the inkjet printing system designed for absorbent surfaces like wood.
Note: This printer cartridge is incompatible with the inkjet printing system for non-absorbent surfaces.

Part #: PC-TSS
Price: $115

TigerSaw 1000 Soft Start
TS 1000 Soft Start

TigerSaw 1000 Soft Start 460 Volts/480V.

Note: Saw System installations and repairs should be done by a TigerStop LLC certified technician.

Part #: SS-TSS
Price: $1,560

TigerSaw 2000 Printer Cartridge
TS2000 Printer Cartridge

This is a printer cartridge for the inkjet printing system designed for non-absorbent surfaces like metal.
Note: This printer cartridge is incompatible with the inkjet printing system for absorbent surfaces.

Part #: PC-TSS-NA
Price: $155

TigerSaw Arbor Belt Drive
TS Arbor Belt

This belt connects the saw motor to the saw arbor in a TigerSaw 1000, TigerSaw 1000G2, or TigerSaw 2000.

Part #: DB-TSS
Price: $155

TigerSaw Back Fence Throat Plate- Generation 1
TigerSaw Back Fence Throat Plate- Generation 1

This is the throat plate for the back fence on the first generation TigerSaw 1000 (models from 2013 and prior). It is not compatible with TigerSaw 1000G2 or TigerSaw 2000.

Part #: BFTP-TSS
Price: $280

TigerSaw Back Fence Throat Plate- Generation 2
TS Back Fence Throat Plate Gen 2

This is the throat plate for the back fence on the TigerSaw 1000G2 and TigerSaw 2000. It is not compatible with TigerSaw 1000G1 (models from 2013 and before).

Part #: BFTP-TSSG2
Price: $280

TigerSaw Cap Guard- Wood
TigerSaw Cap Guard- Wood

These are replacement wooden inserts for the cap guard on older TigerSaws (manufactured prior to 2013). One CG-TSS is a full set of wooden inserts (one each right and left).

Part #: CG-TSS
Price: $365

TigerSaw Idle Pulley Assembly
TigerSaw Idle Pulley Assembly

This is a replacement idle pulley for TigerSaw saw systems.

Part #: BP-TSS
Price: $355

TigerSaw Throat Plate- Gen 1
TigerSaw Throat Plate- Gen 1

This is the throat plate for the table top on the TigerSaw 1000. It is not compatible with TigerSaw 1000G2 (models after 2013) or TigerSaw 2000.

Part #: TP-TSS
Price: $355

TigerSPC Flat Jaw Set
TigerSPC Flat Jaw Set

TigerSPC is a statistical process control caliper set designed to be attached to the TigerStop table system with working lengths from 0-16 feet.The calipers can be equipped with a selection of both standard and custom attachments that allow it to be specifically configured for your set of critical quality control measurements.
The Flat Jaws (FJ) allow operators to measure the distance between flat parts.This item comes with two flat jaws.
There are additional attachments available including:
Mullion/Muntin Half Lap Jaws (HJ) allow operators to measure the center to center distance between two half lap joints.
Miter Jaws (MJ) allow the operator to measure the long side of miter cut pieces.
Swivel Block Attachment (SBA) allows operators to measure from hole center to hole center. It also swivels and can attach to other jaw accessories without losing its reference point.

Part #: FJ
Price: $295

TigerSPC Half Lap Jaw Set
TigerSPC Half Lap Jaw Set

TigerSPC is a statistical process control caliper set designed to be attached to the TigerStop table system with working lengths from 0-16 feet.The calipers can be equipped with a selection of both standard and custom attachments that allow it to be specifically configured for your set of critical quality control measurements.

Mullion/Muntin Half Lap Jaws (HJ) are used to measure the center to center distance between two half lap joints. This item comes with two jaws.

There are additional attachments available including:

The Flat Jaws (FJ) allow operators to measure the distance between flat parts.
Miter Jaws (MJ) allow operators to measure the long side of miter cut pieces.
Swivel Block Attachment (SBA) allows operators to measure from hole center to hole center. It also swivels and can attach to other jaw accessories without losing its reference point.

Part #:HJ
Price: $295

TigerSPC Miter Jaw Set
TigerSPC Miter Jaw Set

TigerSPC is a statistical process control caliper set designed to be attached to the TigerStop table system with working lengths from 0-16 feet.The calipers can be equipped with a selection of both standard and custom attachments that allow it to be specifically configured for your set of critical quality control measurements.
The Miter Jaws (MJ) allow the operator to measure the long side of miter cut pieces.This item comes with two jaws.

There are additional attachments available including:
Mullion/Muntin Half Lap Jaws (HJ) allow operators to measure the center to center distance between two half lap joints.
The Flat Jaws (FJ) allow operators to measure the distance between flat parts.
Swivel Block Attachment (SBA) allows operators to measure from hole center to hole center. It also swivels and can attach to other jaw accessories without losing its reference point.

Part #: MJ
Price: $295

TigerSPC Receiver  
TigerSPC Receiver

Replacement receiver for TigerSPC.

Part #: RCVD
Price: $155

TigerStop Flip Away Set Screw  
TigerStop Flip Away Set Screw

These plastic set screws hold the TigerStop flip away above the beam. This item is a pack of ten set screws.

Part #: NSS
Price: $10

TigerStop Hardware Pack 
TigerStop Hardware Pack

This hardware pack is used for mounting a TigerStop to a table. It contains T-bolts, T-nuts, hex head nuts, and washers (8 of each).

Part #: TSHP
Price: $40

TigerStop Power Cable
TigerStop Power Cable

Power cable for all TigerStop, TigerFence, TigerCrossCut, and SawGear products.

Part #: PC
Price: $50

TigerStop Power Cable 220 V
TigerStop Power Cable 220 V

220V for power cable for all TigerStop products except SawGear.

Part #: PC220V
Price: $50

TigerStop UV Scanning Pusher Foot
TigerStop UV Scanning Pusher Foot

TigerStop's Scanning Pusher Foot can be used on standard TigerStops as well as TigerSaw 1000s and TigerSaw 2000s. Mark defects with a UV crayon and the Scanning Pusher Foot will scan material and cut out the defects while optimizing the clear material.

Part #: SCAN-UV
Price: $6,300

TigerTouch Tablet
TigerTouch Tablet

Any TigerStop can be enhanced with cutting edge touch screen control with TigerTouch™. Using the TigerTouch touch screen controller, you can download an infinite number of cut lists, display three cut lists at a time for easy switching between work orders, and view statistics such as job status, remnants, remaining parts, and yield.
Replacement TigerTouch Tablet PC's come pre-loaded with TigerStop's state of the art TigerLink6 Cut List Downloading software (DNLD), TigerSet (SET) to control peripheral devices, and Dynamic Optimization software (OPT).
Note: This item comes with just the touch screen, not the entire tablet package. If you'd like to purchase the entire tablet package for your machine search for part: TABLET-PKG.
Important Information About Ordering This Item:
TigerTouch is incompatible with machines that are not already enabled for TigerTouch. Email service@tigerstop.com prior to ordering this product if you are interested in adding tablet control to an existing TigerStop machine.

Part #: TABLET
Price: $2,075

TigerTouch Tablet Package
TigerTouch Tablet Package

Any TigerStop can be enhanced with cutting edge touch screen control with TigerTouch™. Using the TigerTouch touch screen controller, you can download an infinite number of cut lists, display three cut lists at a time for easy switching between work orders, and view statistics such as job status, remnants, remaining parts, and yield.
TigerStop's Tablet Package includes a touch screen, a protective case, control stand (SMTCS), and cabling. It also includes three types of software: TigerLink 6 Cut List Downloading (DNLD), TigerSET (SET), and Dynamic Optimization (OPT).
Important Information About Ordering This Item:
The tablet package is incompatible with SawGear and with electronics older than version 5.60.
TABLET-PKG orders require the serial number of the machine that will receive the electronics. Without the serial number this part will not ship. Email your serial number to orders@tigerstop.com
If you have trouble finding your serial number watch the how to video below. For additional help contact service@tigerstop.com
Note: If you want a tablet package for your TigerSaw 1000, TigerSaw 2000, or TigerSaw Miter, you will not need the controller stand (SMTCS). The tablet package mounts differently on saw systems using a separate mounting hinge.

Part #: TABLET-PKG
Price: $3,695

TigerTurbo Carriage
TigerTurbo Carriage

TigerTurbo Carriage

Part #: STOP-TT
Price: $855

TigerTurbo Gangstop
TigerTurbo Gangstop

This is a flat pusher attachment for the TigerTurbo or the HeavyDuty 2. The pushing surface is 12 by 4 inches (30.5 by 10.2 cm). This attachment's reach is 20 inches (50.8 cm) beyond the leading edge of the carriage it is attached to. GSX-TT/HD2 orders must specify a left-handed or right-handed orientation. Left-handed means that the positioner is to the left of the integrated tool (a TigerTurbo to the left of a drill press, for instance).

Part #: GSX-TT/HD2
Price: $1,040

TigerTurbo Internal Stop Carriage
TigerTurbo Internal Stop Carriage

TigerTurbo internal stop carriage replacement.

Part #: ISC-TT
Price: $2,890

TigerTurbo Motor
TigerTurbo motor

This is an AC motor for the TigerTurbo.
Important Information About Ordering This Part:
MOT-TT is incompatible with version 4 electronics.
This part may require a software upgrade or a Conversion Kit (CON5-CONV).
The TigerTurbo DC motor is no longer available. Contact service@tigerstop.com for more information.

Part #: MOT-TT
Price: $2,725

TigerTurbo Motor Conversion Kit
TigerTurbo Motor Conversion Kit

This kit contains the parts needed to upgrade a TigerTurbo from the older DC motor to the modern AC motor.
Important Information About Ordering This Part:
AC-CONV is incompatible with electronics prior to version 5.40.
Please contact TigerStop customer service if you are considering purchasing this kit: service@tigerstop.com
AC-CONV orders require the serial number of the machine that will receive the electronics.

Part #: AC-CONV
Price: $3,635

TigerTurbo Motor Drive Belt
TigerTurbo Motor Drive Belt

TigerTurbo motor drive belt.

Part #: DB-TT
Price: $50

Tilted Table Brackets
Tilted Table Brackets

These brackets attach the legs to the table for all tilted TigerStop feed tables. They are incompatible with SawGear tables and with flat TigerStop feed tables. One TABBR-T, sufficient for one leg set, contains two brackets, four binder rings, and a table hardware pack.

Part #: TABBR-TT
Price: $230

U Slot
U Slot

This hard plastic trim fits snugly in the T-slots on TigerStop extrusions, and is sometimes used to conceal and protect small cables. U-slot is ordered in 1 foot (0.305m) increments. There are four orange U Slots per TigerStop that travel the length of the extrusion.

Part #: USL
Price: $2

Universal Bracket
U Bracket

You will need the following number of Universal Brackets (UBR) depending on the type of machine you have:
SawGear: 1 Universal Bracket (UBR) for every 3'
TigerStop: 1 Universal Bracket (UBR) for every 3'
TigerTurbo: 1 Universal Bracket (UBR) for every 24"
HeavyDuty 2: 1 Universal Bracket (UBR) for every 24"
* Note:The UBR comes with 1 hardware pack (F0032) per quantity ordered.

Part #: UBR
Price: $50

UV Crayons

UV Crayons

This is a box of 50 UV crayons for use with the crayon defecting option on TigerSaw 1000, TigerSaw 1000G2, or TigerSaw 2000.

Part #: UVC
Price: $135

Version 4 Controller Cable

Version 4 Controller Cable

20' controller cable for the Version 4 controller.
This 25-pin cable connects an SMT controller to an AMP2 amplifier (version 4 electronics). It is incompatible with CON5 or AMP6. SMTCC is 20 feet (6.1 m) long.

Part #: SMTCC-20
Price: $245

Version 4 to Version 5 Controller Conversion Kit

Version 4 to Version 5 Controller Conversion Kit

The conversion kit is a discounted bundle of version 5 electronics. Replacement of electronics that are no longer available is possible with this upgrade path. It is always a good idea to contact TigerStop customer service to avoid surprises when considering an electronics upgrade.

Important Information About Ordering This Part:
CON5-CONV orders require the serial number of the machine that will receive the electronics. You must email your serial number to orders@tigerstop.com for this part to be shipped to you. (Failure to use the parts with the specified serial number can result in software compatibility issues.)
If you are having trouble locating your serial number you may email service@tigerstop.com or watch the below short video.
The CON5-CONV price includes a $400.00 core charge, refunded if the previous electronics are returned to TigerStop within 30 days of the new shipment.

It's important to test the motor before ordering a CON5-CONV, because a damaged motor can destroy a fresh amplifier. Watch the below video to learn how to test your motor.

Conversion kits are incompatible with SawGear and with older TigerStops that have a yellow motor box.
The kit does NOT include a control stand, an I/O Panel, or a motor.

The CON5-CONV Kit includes the following items:

  • Version 5 controller (CON5)
  • 10' or 3 meter long controller cable (CC5-10)
  • Power Cord (PC)
  • Amplifier (AMP6)
  • Quick Reference Instruction Cards

Part #: CON5-CONV
Price: $3,125

Wired Barcode Scanner Kit

Wired Barcode Scanner Kit

TigerStop offers a wired barcode scanner kit which comes with SET software to communicate to peripheral devices, and an I/O Panel.
The barcode scanner can be used to move your TigerStop to a position and manage cut lists. With your bar code scanner, you can build cut lists and then optimize those cut lists using Dynamic Optimization software.

Part #: BCS-KIT
Price: $2,540

Wireless Barcode Scanner

Wireless Barcode Scanner

Barcode scanners can be used with TigerStop, TigerFence (and SLR), TigerCrossCut, TigerTurbo, TigerRack, and HeavyDuty 2. The wireless barcode scanner comes with the scanner base, data cable, RS232 cable, and the power supply.
Barcode scanner compatibility requires the SET software feature (purchased separately and used to open up communication to peripheral devices). To use a barcode scanner while the TigerStop is connected to a computer, an I/O Panel (purchased separately) is required.
Note: to purchase a Wireless Barcode Scanner Kit that includes an I/O Panel and SET software search for part number BCSW-KIT.

Part #: BCSW
Price: $1,715

Wireless Barcode Scanner Kit

Wireless Barcode Scanner

TigerStop offers a wireless barcode scanner kit which comes with SET software to communicate to peripheral devices, and an I/O Panel.

The barcode scanner can be used to move your TigerStop to a position and manage cut lists. With your barcode scanner, you can build cut lists and then optimize those cut lists using Dynamic Optimization software.

Part #: BCSW-KIT
Price: $3,140

Zero Clearance Throat Plate- G2

Zero Clearance Throat Plate- G2

This is the throat plate for the table top on the TigerSaw 1000 (second generation model, 2013-current) and TigerSaw 2000. It is not compatible with TigerSaw 1000G1 (models from 2013 and earlier).

Part #: TP-TSSG2
Price: $355

Additional Parts Available

 

Acorn nut for TigerStop Tie Rod $.70
TigerStop Electronic Measuring System Belt for 16' TigerStop - New $1,200.00
TigerStop Electronic Measuring Far End Carriage Assembly - New $270.00
TigerStop Electronic Measuring Far End Carriage Assembly - USED $220.00
TigerStop Electronic Measuring System $595.00
Scroll to top